How to correct the fishing line on the spinning spin for long casting, in which direction: scheme

From this article you will learn how to wind a fishing line on a spinning reel.

Proper winding of the forest thread on the spinning reel is the key to successful fishing. If something is done wrong, then there will be a breakdown or disruption of the forest thread from the coil. In this article, we will consider how to wind the fishing line not only on the reel of fishing rods, but also a trimmer. Read further.

How to correct the fishing line on a spinning spin for long casting, in which direction: scheme, video

For the first time it will be difficult to wrap the fishing line yourself, but following the instructions, you can do it right. Here is a phased scheme for winding the fishing line to the spinning spin for long casting:

• First remove the bobbin and install the bobbin. Pull the forest thread into the ring and attach it to the bobbin. If there is such a spare device, then first practice and wind the forest wire on it.
• There is a hole in the center on the reel bobbin. Put the bobbin on a pencil or pen and begin to wind it.
• In order not to injure your hands when winding the forest thread, put on gloves. Pour the fishing line slightly higher than the first ring is located. With one hand, adjust the winding process on the bobbin, and the other - twist the bobbin, but slowly, slowly.
• It is necessary to wind the forest wire until there is no more than 2-3 mm from the edge of the bloom. It is not necessary to wind up to the edge, since the forest wire can pass in the form of loops.
• If you are winding on a spare rogue, now rewall the forest thread to the main device. If the degree of winding does not suit, adjust it with special goals.
• Now attach the end of the forest thread for the clip, the protrusion on which is located on the side of the spray.

In this figure, a detailed winding scheme is visible. It also shows which way that the forest thread needs to be wrapped in.

Here is a video that will help you properly wind the forest wire. Just follow the tips in this video and repeat, following their steps. Choose any convenient way of the three videos presented in this.

Video: How to wrap a fishing line on an HD coil correctly?

How much fishing line is wound on a spinning reel: how many meters, what fishing line?

For each coil, the amount of meters is individually, since it can have its own individual diameter and height of the side. Everything will still depend on the parameters of the acquired forest wire. So, how much fishing line is wrapped on a spinning reel, how many meters, what fishing line?

In this particular case, you should adhere to such a rule:

• The fishing line should not reach the edge of the sides by 1-2 millimetersbut not exceed 5 mm, since the long cast will become impossible.

The coils always indicate the labeling of forest intensity. For example, if we take a fishing line with a diameter 0.25 mm, then we can wrap up 153 m, and with diameter in 0,30 mm can already be wound only 106 m.

Thickness:

• The golden middle is a fishing line in 0.25 mm, since it withstands the load on the gap in 6-8 kg.
• For catching pike perch, pikes are better to use a fishing line before 0.35 mm, and it will fit the perch 0.16-0.2 mm.

As you can see, everything is also individual here. In any case, when buying, the seller will be able to recommend something to you depending on which “predator” you go to.

How to wind a fishing line on an inertial spinning coil?

If you bought a spinning, but do not know how to use it, you need to see the instructions attached to it and check with it. According to the classified class, an inertial coil should be suitable for this rod, as well as for its cord. An inertial coil is interesting in that it does not directly participate in throwing spinning into the water. How to wind a fishing line on an inertial spinning coil?

It is worth noting: Sometimes a trophy fell on a hook - fish - can "choose" up to 200 meters Fishing lines, especially if this water animal is distinguished by a predatory character, which also often happens. Therefore, you need a good supply in the length of the fishing line.

The fishing line in the spinning rod is knitted to the drum with one end, the other to the cord. This is a feature of the winding of the fishing line on this type of coil.

Professional fishermen advise: Before starting to study the correct winding of the forest thread on the coil, you should first buy backing.

Backing consists of synthetic fibers, which are laid on a spool from 10 to 100 meters. Due to this device, the diameter of the drum increases. Thanks to this, the rounds of the cord will be located correctly, closer to the side of the spool.

Experienced fishermen note:Many make an error when preparing spinning to work.

There are only two correct winding methods:

1. When the fishing line is located against the rotation of the inertial coil.
2. When it is located on the rotation arrow.

If you place a line by rotation, can turn out a "beard". In this case, it will be difficult to withstand the process of reducing fish in this case. The forest thread will constantly get confused.

The location of the fishing line against the movement of the coil - The most true way, since it is in this case that the coil drum will rotate correctly, and there will be no “beard”. That is, if you wind the fishing line clockwise, the coil can drop the fishing line, if against the hourly one, it will spin correctly. In other words, the forest wire in a spinning rod with an inertial coil should be wrapped along the rod - everything is simple.

How to wind a fishing line on an underdevelopment coil alone: \u200b\u200bvideo

The procedure for winding the fishing line on the underlying coil is one of the simplest. It can be carried out alone, without assistants. Here are the stages:

• Put on the bobbin on the metal pin, which must be pre -fixed staticly. It can be a pencil, a spoke or a long screwdriver. The main thing is that Bobinka spin freely.
• Pass the forest wire through the rings and tie the knot. Start start with mounting on the rogue.
• Now raise the arc of the forest ash and wrap the forest thread along the spool. Make another knot and tighten. Lower the forestry.
• Under the fastener, you can stick a patch or attach a piece of an elastic band cut off from an attack. This will help the forest wire correctly wrap it up and it will not slip.
• Now wind the forest thread rotating the hilt.
• The fishing line should be in a stretched position all the time. To do this, hold a bobbin with your free hand.

Watch the video. In it, an experienced fisherman tells how to wind the fishing line with one with backing.

Video: winding fishing line with backing to a reel

How to wind a fishing line on a reel: tips

The main thing is that when winding the fishing line on the reel, this is a serious attitude to this matter. Indeed, if it is wrong to wrap the quit -sized thread, the loop may be dropped, and then you will have to not remove the fish, but to unravel a lump from the fishing line for a long time. So how to prevent mistakes? Tips:

• Crick the bobbin to a rigidly placed flat stick, pen, knitting needle and a similar object. Most importantly, the fishing line should be perfectly flat - it is very important.
• You will need one more free hands. But, if there is no one to help, then you can do in this process and yourself. The instructions are described above how to wind the forest thread to one.
• Then stretch the fishing line through the ring, and at the end tie the knot.
• Then attach the forest thread on top of the bobbin in a circle, before raising the arc of the forester, and after the next tightened knot, lower the arc.
• It is important to ensure that the fishing line is not at the level of the bastard to avoid the discharge of the loops. As described above, it is best to leave 1-2 millimeters to the side and preferably no more
• Ready.

For many fishermen, it is important when winding the forest thread, from which material the spool is made. Read about this below.

How to wrap the fishing line on the rogue, on which rogue to wrap the fishing line - plastic or metal?

It was described above how to correctly wind the fishing line on the spinning or fishing rod coil. But it is of great importance how you tie the forest thread to the bundle. If you tie it incorrectly, then a large fish can break, or the forest thread will scroll and confuse. In the direction of the winding direction, it is necessary to glue a piece of isolets for convenience.

It will be easy to tie using the use of such methods:

• A self -tightening double loop
• Clinch
• Special node for better fastening

Take a look at the drawing. It shows in detail two methods for tying fishing line on a bastard.

Another question that concerns many inexperienced fishermen - what bobbin to wrap the forest wire - plastic or metal? Many believe that the metal spool is intended only for a wicker rope, and plastic - for the forest thread. But this is a misconception.

Previously, there were only plastic bursts, and they perfectly coped with their function.

It is worth noting: The metal spool will be polished much easier.

How to wind a fishing line on a multiplier coil?

This process will not seem difficult for you, but it is important for successful fishing and good mood in its process. Incorrect winding of the fishing line is fraught with confusion at the most inopportune moment. Undoubtedly, the resulting “beard” will not allow you to get a good catch. How to wrap a fishing line on a multiplier coil?

Unlike the underlying coil, winding for the multiplier device will happen much easier and does not have any different options or methods. There are three basic rules in its process:

1. The fishing line is tied to the coil in the hole conceived by the design. In this case, it makes sense to use such a node that will definitely not be angry and will hold the end tightly.
2. The rings should be pressed tightly - one to one. The fishing line should be well pulled and, rotating the handle of the product, put the ring behind the ring.
3. Subsequent layers of the forest thread should not be crossed with each other. Such a consistent and flat winding prevents confusion.

This is the whole process of winding the fishing line. It is worth noting that it is important to pull the thread well so that it lay tightly on the coil and subsequently cannot cross and confuse.

How many fishing line is it to wind on the vent?

Gervice is an effective device for catching predatory fish, for example, with its help you can catch a pike. Knowing the rules for its installation, including the number of required fishing line, will be able to provide a good result. Little line for gerlitsa: how much do you need to wash?

• The amount of fishing line on the vents should exceed the depth of the reservoir by 3.5 - 4.5 times.

It is important to understand: The value is calculated not from the highest depth of the reservoir where fishing will occur, but from the place where the burial itself is installed. When taking into account the fact that such a design is not placed to a depth exceeding 4 meters, more than 15 meters of fishing line on the vents are not washed.

• The length of the required fishing line varies depending on the bottom of the reservoir.
• If it is abnormal, there are many snags and other “interference”, then the length of the fishing line should exceed a depth of no more than 2.5 maximum 3 times.

Such parameters of forest wire limits the pike in movements and prevents it from confusing the vents in underwater vegetation. If the bottom is bad, then you should be prepared for the fact that the fish will be restless. It will actively confuse the fishing line, dive sharply deep into it - make candles, can wrap the tackle around the pole, therefore, pull out the entire structure entirely.

How to wind a fishing line on a trimmer coil, mower, benzo -oxy: video

A trimmer, mowing or benzocoses work as well as a rod with a forest thread. Only in the spinning rope is needed to throw the rod, and in the trimmer it is necessary in order to cut greens. How to wind a fishing line on a trimmer coil, mower, a benzo -swindle? Here are the stages:

• Dismantle the spool From the coil box.
• On a coil with one osmus There are notes in the form of indicating arrows. They show the side of the winding, you will need from 2 to 5 m of the forest thread.
• For a trimmer head with two mustache You will need from 1.5 to 3 m. Wound the forest wire in the opposite direction of rotation of the head.
• Trimmer head with a pavement of the forest rope It is just refuel: correctly season and fix the ends. The tool in automatic mode will perform winding, you only need to turn it on.

Video: How to wind a fishing line on a mowing head of a trimmer or motorcycles?

It is easy to work with this design and it is easy to season the fishing line, but it often becomes unusable and is expensive. Therefore, a trimmer head with one or two mustache is very popular.

Now you know how to wind the fishing line on the spinning and coil of the trimmer. To do it just alone, without assistants. Good luck!

Video: How to wrap a fishing line on an underlying reel?