The washing machine jumps when squeezing linen: reasons, what to do to eliminate?

The causes of excessive vibration when pressing the washing machine and the methods of eliminating it.

The washing machine is one of the favorite devices of modern housewives. Because it is with its help that you can devote a few minutes of time, instead of engaging in washing. The washing machine often breaks, and the breakdowns can be very unexpected or vice versa provoked by improper operation of the equipment. In this article, we will tell you why the car jumps and vibrates greatly during washing.

Why is the washing machine jumping when spinning linen: Reasons

This may be associated with certain problems, or due to improper operation of the equipment.

Strong vibration, shaking of a machine associated with improper operation of the equipment:

• Immediately after the purchase, many housewives are in a hurry to run the car without really reading the instructions. Therefore, often inside remain transport boltswho hold the drum in a fixed position. This is necessary so that the technique in the process of delivery is not damaged. If you do not extract the bolts, in the process of washing the car will shake, and also throw from the side to the side. They must be pulled out.
• Incorrect equipment adjustment. Be sure to look at how your car is on the tile. In the case of improper adjustment or if one leg is below the other, the car is uneven, it is overwhelmed. Which also provokes an increase in vibration during washing. It is necessary to set the level on the machine and leve it, rotating the legs in the necessary direction.
• Slippery floor. Often the car vibrates due to the fact that it is installed on a glossy tile. Thanks to this, a very small clutch force. Therefore, the equipment is strongly introduced from the side, it makes noise, vibrates and stagger. The problem is solved very simply: a rubberized rug is acquired. The technique is installed directly on it.
• Uneven loading of linen. The machine can vibrate due to the fact that you are erasing a duvetel with sheets, as well as pillowcases. The fact is that in the process of washing a lot of things is stuffed into the holes of the duvetail. Accordingly, everything is knocked into one pile, and the machine is loaded unevenly. It turns out that a whole lump of linen rotates in the drum. It is necessary to turn off the car out of the network, drain the water and pull the bed out of the duvetail, evenly level it, distributing it inside the drum. You just need to distribute all things and only then carry out the washing.

These causes are not related to breakdowns, but provoked by exclusively improper operation of the equipment. But there are other reasons why the car vibrates and staggering greatly during washing. They can be associated with breakdowns, as well as problems in the work of equipment.

What to do if the washing machine jumps when squeezing linen: elimination options

Damage associated with vibration:

• Depreciation wear. There are special shock absorbers in the car that extinguish the fluctuations of the drum and prevent its vibrations, as well as shaking. When the shock absorbers are out of order, the car begins to vibrate very much. They need to replace them.
• Wear or damage to springs. The fact is that in washing machines, a counterweight to the drum is hung. This is a concrete stone that allows you to maintain balance and not hang out the drum from the side. Accordingly, if this counterweight is destroyed or the bolts are promoted, with which it is attached to the device, the machine begins to jump. It is necessary to tighten the bolts or replace the counterweight in case of its destruction.
• Bearing malfunction. Often in the bearing during prolonged work, backlash occurs. Accordingly, its walls become thinner, the bearing should be replaced immediately. If it is scattered during the operation of the unit, its fragments can hook other components of the machine, as well as damage the tank and other spare parts.

In order to determine what caused the jumping of the machine, it is necessary to clarify the age of household appliances, as well as the conditions in which it was operated. Most often, malfunctions in new devices are not connected with operation, but with improper installation, the presence of locking screws inside the equipment, which forgot to pull out after transportation. It is possible to adjust the legs and carefully follow the instructions.

Do not overload the device. Everything is much more complicated if the unit is old enough. Most likely there is some kind of breakdown. It is necessary to repair and replace components, in case of their breakdown.

Video: The machine jumps when spinning