Vinegar and soda for cleaning pipes: Rules for use - how to use? How to clean the pipes with soda and vinegar with salt, hydrogen peroxide, boiling water?

Methods of cleaning pipes with soda and vinegar.

Content

Zoror in the sewage system is a fairly common problem. It occurs if the hostess ignores the rules of purity. Of course, the situation in the kitchen very often saves the net, it holds most of the garbage, but cannot cope against fat. Special chemicals, as well as soda with vinegar, will help to deal with this problem. In this article we will consider these methods.

Vinegar and soda for cleaning pipes

To use chemicals, you need a lot of attention, as well as caution. The fact is that chemicals contain acid, alkali. They can affect the integrity of the pipes, especially if they are old and made of metal. This can lead to corrosion, as well as the destruction of the pipe.

For cleaning, you can do as follows. Clean the chintz in the sink with your fingers, removing large garbage. After that, half a glass of sodium bicarbonate must be poured into the drain hole. Further, 200 ml of table vinegar is poured into the drain hole. Its concentration should be 9%. After that, a violent reaction will be observed in the pipe. So that unpleasant odors do not spread throughout the kitchen, the drain hole must be closed with a lid. Now you need to detect about 2 hours, and during this time do not go into sewer pipes

After such a manipulation, most likely, the water will successfully pass. This method is advisable to use if the drain hole in the kitchen is clogged with fat deposits. Against some hair, rags, or more serious contaminants, soda with vinegar work quite poorly. They are gentle and not very aggressive means. But in the case of blocking the sink in the kitchen, they can do it well. For manipulation, you can use other options for using soda with vinegar.

Salt, soda and vinegar for cleaning pipes

Instructions:

For cleaning, it is necessary to remove large garbage from the drain hole. After that, it is necessary to pour into the sewer pipe near a liter of almost boiling water. Water should be very hot. After that, you must wait for about 30 minutes.
Further, a glass of baking soda is poured into the drain hole and 50 ml of hydrogen peroxide is poured. After that, the drain hole is closed with a dense plug, and is left for about half an hour. Next, cleaning is carried out with a vantuse.
The principle of operation of such cleaning is that soda with peroxide corrode particles of fat, dilute pollution, making it more porous, and simplify the pushing. Accordingly, after such manipulations, you can resort to the use of a vantuse, which will be quite effective.

This is not the last way to use soda. You can use another method. By mixing different reagents with soda, vinegar, salt, peroxide, chlorine, you can achieve the maximum quality of cleaning.

Instructions:

One of the most effective ways to use soda is mixing with salt. This composition perfectly corrodes fat deposits, as well as small particles of food. In addition, it allows you to disinfect the pipes, to prevent the occurrence of an unpleasant odor, and the decomposition of food particles inside the pipes.
To carry out manipulation, it is necessary to mix salt in equal amounts along with food soda. It is best if food salt is quite finely grinding and not contain iodine. After that, the drain hole is cleaned of food residues, and a liter of hot water is spilled.
Next, a mixture of salt and soda is filled up. The total amount of the mixture should be approximately one glass. After that, you must not use the drain throughout the night. That is, it is best to carry out such manipulations late in the evening to wake up early in the morning, and use the cleaned sewer.
Early in the morning, it is necessary to open the plug of the drain hole, and pour even a liter of hot water into it, which has recently boiled. After carrying out all the above manipulations, you will be able to get rid of the remains of sticky fat in the pipes.

How to clean the pipes with soda and vinegar with hydrogen peroxide: the rules of use

Rules for the use of soda and vinegar:

Without fail, when manipulating, it is necessary to use rubber gloves. They will prevent aggressive products from entering the skin, and will prevent irritation. It is also advisable to use glasses, they will prevent aggressive vinegar from getting into the eyes.
After the manipulation, in case of ineffectiveness, the drain must be washed with a large portion of water. It is also worth acting if you use soda with vinegar, after the use of industrial methods, and aggressive chemicals.
That is, after using alkali, acid, mole, and similar products, you should not use soda with vinegar. The fact is that when the interaction of these chemical reagents, the discharge of dangerous vapors, and aggressive substances that harm health can be observed. In order to use another method, it is necessary to rinse several times with hot water.
In order not to bring the sewer to a deplorable state, it is necessary to conduct preventive cleaning from time to time. It consists in falling asleep 2 glasses of table salt, in the drain hole, and the use of boiling water. Such manipulation is performed once a month. This allows you to prevent the occurrence of serious blockages, and also prevents the deposition of fat on the walls of the pipes.

As you can see, with the help of soda with vinegar, you can easily eliminate the blockage. This method works only if the deposits in the pipes are new and soft. Otherwise, you will need the use of more serious chemicals, or a plumbing challenge.