The washing machine refuses to squeeze and drain water: cause and repair.
Content
Specialists for repairing household appliances very often meet with such a problem as the lack of spin and drain water in machines: Samsung | Samsung, LG, Indezit | Indesite, Bosch | Bosch, Kandlant, Atlant, Zanussi, Ardo, Ariston. In this article, we will consider the main causes of this problem and possible ways to eliminate it.
Why the washing machine does not drain water and does not squeeze the laundry: reasons
![](http://heaclub.ru/tim/b64f3ff89e4f6b6287148e5df6395476.jpg)
The most common problems:
- In the absence of water drain:
- There was a clogged pipe or drain filter
- Pass failure or breakdown of the pump
- The setting of the programmer or control module has flown
- The water level sensor has become unusable
- In the absence of spinning:
- Incorrectly established mode without this function
- A program for washing with low speed was selected. Which leaves linen too wet. In models: Samsung, LG, Indezit, Bosch - there is the possibility of changing the number of revolutions. They are probably inadvertently reduced, so the linen turned out to be excessively wet
- The drain system does not work. The pump became unusable
- Non -serviceability of the water level sensor
- The module broke
- The engine burned
- Revolutions are not carried out due to a broken sensor
In modern models of machines, most often in the brands of Kandy, Atlant, Zanussi, Ardo, Ariston, special displays are built -in, on which the digital designations of the errors that have arisen are displayed. This makes it possible to accurately diagnose the problem.
What to do if, the water in the washing machine does not completely merge?
![](http://heaclub.ru/tim/d00001842a4138248e1a1fa3fe1dbb90.jpg)
- First of all, check which program is installed for washing. Apparently a function did not provide for water drainage
- If the problem is not related to the program:
- We drain the water in one of the ways:
- Pull out the cord from the machine from the outlet
- Remove the lid from the drain filter
- Without pulling out its basis the filter, we pull out a small tube (if any)
- We direct the end to pre -prepared containers
- Or lower the drain hose to the floor level
- After draining the liquid, remove the linen and squeeze manually
- Then we make a visual review, with the elimination of small errors:
- We check if the drain hose is somewhere
- We clean it, separating it from the unit, using a powerful water jet. Maybe the reason is that the hose is clogged
- Inspect the garbage filter for garbage, if necessary, delete pollution
- Rinse the filter in soapy water. If you do not do this periodically, a contaminated filter can cause the problem under consideration
- Inspect the pipe connecting the tank with a pump. Maybe it needs to be cleaned
- Remove and clean the pump
- If, after eliminating minor reasons, the machine did not start working in normal mode, then there are more serious breakdowns listed above. In this case, it is better to call the master.
Video: Why does the washing machine not drain the water? Secrets of the seller of household appliances
What to do if drain and squeeze in the washing machine?
![](http://heaclub.ru/tim/38e7278af64b785311b1fe976b8d88a5.jpg)
If there is no way to use the services of a trusted specialist, you can try to eliminate the malfunctions with your own hands.
- Disconnect the washer from the water supply, sewage and electricity
- Cover the center of the free room with rags
- Move the unit there
- Lower it on the floor sideways
- Check and repair the pump
After eliminating the blockages, the machine continues to issue the same error, it is necessary to check the performance:
- Remove the drain pump
- We check the resistance with a multimeter, if zero or one is displayed on the scoreboard, then the pump has burned down, you need to buy a new one and change it
- With a normal working mode, electricians, we are looking for a problem in the operation of the mechanism completely
- Check the density of the impeller planting on the axis
- We examine if there are unnecessary wound objects (hair, thread) based on the impeller
- At the same time, we check if the wires and terminals that attach a pump with a drain pump have fired or jumped out
- If there are no problems with pomp, we proceed to check the next part
- We make a test of the Pressostate work
- Remove the top cover from the washing apparatus
- We take out a water level sensor
- We check if there are external damage or blockages. We clean it if necessary
- We check the performance of the device itself as follows:
- We pull a small hose onto the fitting, blow it, bring it to the ear: if the sound is heard in the form of a click, then the part is serviceable, if not you have to change it
- We test the control module
- He will cope with electronics on his own problematic. Therefore, at this stage it is better to contact the master
- The only thing that can be done yourself to feel and inspect all the wires going to this details, check them with a multimeter
If the washing unit Samsung, LG, Indezit, Bosch, Kandlant, Atlant, Zanussi, Ardo, Ariston, does not want to drain water and squeeze the underwear, look for without delaying the problem of its “behavior”. Over time, a meager difficulty can turn into a serious and expensive repair or complete replacement of the device.