Do -it -yourself bird feeders from plastic bottles: ideas, description, instruction, photo. How to make a bird feeder of 1.5 liter, large 5 liter plastic bottle, from 2 bottles?

Making bird feeders from plastic bottles.

Content

A bird feeder is a very necessary thing both at the beginning and at the end of winter. Indeed, during this period, birds especially need food. In this article, we will learn how to independently make feeders from plastic bottles, because this is the most just a way to get an excellent result.

How to make a bird feeder from a 1.5 liter plastic bottle in stages?

Bird feeding is not only an interesting occupation, which allows you to observe feathered, but also bringing great benefit of living nature. The feeders are made from a wide variety of materials.

One of the most popular and easy to manufacture is a plastic bottle. It has a number of advantages:

availability
cheapness (you don’t pay for it, it is given “in load” to the drink)
easy to manufacture (thin plastic is easy to cut and bend)
wind protection and precipitation
temperature drops

We offer you the following types of feeders made of plastic one and a half liter bottles.

"Original"

Prepare:

actually a bottle
2 tablespoons wooden with long handles
wire

Performance:

retreat from the bottle-dint 7-10 cm
make two holes opposite each other from two opposite sides
insert one spoon through them
back up another 10 cm
make the following holes so that the second spoon, reached through them, is located perpendicular to the first
expand a few holes near the widespread sides of the spoons - so the food will be easy to get enough sleep
tie the bottle throat with wire
hang on a tree

"Bunker"

take 2 1.5 l bottles
in the lower part of one, make 2 round holes (retreating from the bottom about 8 cm)
turn the second bottle and insert the first
the neck should not reach the bottom a little
pour the grain or any bird food
birds will eat food, and its next portion will gradually get out further

How to make a bird feeder from a 5 liter plastic bottle?

The plastic bottle of 5 liters is one of the most suitable materials for performing the feeders, since it is:

has a wide bottom on which a larger number of birds can fit
has a good capacity that allows you to pour a lot of food

We offer two types of feeders from such a container:

Horizontal:

put the bottle on the side
on two opposite sides by the marker, draw horizontal rectangles
cut the lower and side sides of the rectangles along the intended lines with a sharp knife
bent a piece of plastic
walk along the fold line with pliers - it turned out a visor that protects birds from the rain
in the lower part of the bottle, make two holes opposite each other
pass the wand through them - it turned out to be
with a needle at the bottom of the feeder, pierce small holes through which water will drain during the rain
make a hole in the bottom of the bottle
pass through it a rope
tie the other end of the rope on the neck
piece the feeder by the resulting loop on the tree

Vertical:

on all sides of the bottle, cut through the large enough windows
cut 4 pieces from the old cable, the length of which is equal to the width of the window
cut the cable along
put on the resulting blanks on the lower part of the windows - a reliable protection of our birds from injury is obtained
below the windows make holes
through them, pass the wands-jackets
make a hole in the bottle cover
stretch through it wire or rope
tie, making a loop

How to make a bird feeder of 2 plastic bottles?

Of the two plastic bottles, it is easy to make practical self -filled feeders. We offer the following methods.

Method 1:

take 2 identical bottles with a volume of 1.5-2 liters
in the bottom of one bottle, make several small holes to remove moisture
cut the top - it will not be needed
at the top of the remaining lower part, make the holes
stretch the tape through them and fix it by tied nodules inside the container
cut the windows from two opposite sides
fill the second bottle to half
turn it over and insert it into a cut bottle so that between the neck and the bottom there is no more than 0.5 cm
wrap the structure with wide tape along the seam of the bottle connection
slue behind the tape

Method 2:

prepare bottles of 5 liters (base of the feeder) and 1-1.5 l (dispenser with food)
take measurements of containers in advance - a small bottle should be placed in a large one, resting on its neck with its lower part
in the Bolshaya Bablag, on two opposite sides, cut out the inputs of birds
in the lid, make a hole through which pass the rope mount
cut the bottom of a bottle of small volume
on her neck, make 2-3 holes with a hot nail, from where the grain will be poured
insert a small bottle into a large neck with a neck
pour the food
twist the cup with a lid with a rope loop with a lid
hang on a branch
such a feeder made of bottles of contrasting color will look original

Method 3:

you will need thin plywood and two bottles, one of which is a little more than the other
cut a large bottle into three equal parts, of which only the bottom and top will be needed
cut the edges of the top with smooth waves, and cut the neck - the “plate” with a hole in the center turned out
in the bottom of a small bottle, cut a hole into which the feed will be embroidered
right the holes in the middle of this bottle
pass the rope through them and tie it so that you can then hang the structure
near the neck of the small container, pierce several holes
turn this bottle over this bottle and take its neck in the "plate"
in the center of the plywood, cut a circle
put on the plywood on the neck
twist the lid - it turned out a place for landing
pour the food into a small bottle through the hole made
cover cut off the lower part of a large container
hang the rope

How to make a simple bird feeder from plastic bottles?

In the case when there is no time to make a complex feeder, and the desire to help the poor feathered is present, you can use our options for making the simplest feeders from a plastic bottle.

Option 1:

take a bottle with a volume of 1.5 to 5 liters
retreat from the bottom of about 4-5 cm
make a wide hole with a sharp knife
pour the edges of the holes with electrical tape so that they are not too sharp
on the bottom inside the bottle, put a piece of thin plywood or other dense material (tile, linoleum) in order to tighten the feeder
tie a wire or rope to the neck of the bottle
fasten on the branch
do not forget to fall asleep food

Option 2:

in 5-Lin, cut the bottom and neck
place the resulting cylinder horizontally
at the top of the workpiece on the sides, make two holes
stretch a rope or wire through them
for the resulting loop, pull on a branch
pour the grain or pieces of old fat for a blue inside inside

Option 3:

prepare a 2-liter bottle
cut the top
having retreated from the bottom about 7-8 cm with scissors, cut the front of the bottle
attach the finished feeder with screws to the rear wall to the fence, wooden wall or tree trunk

Prepare grain, cereal and seeds for feeder

How to make a beautiful bird feeder from plastic bottles?

Bird "dining room" can be not only practical, but also beautiful. It is not at all difficult to do this. Only a little time and patience will need. We offer a choice of such options for pretty feeders.

"Color House"

Prepare:

a two -liter bottle
bchev
paints

It is easy to do:

cut the top from the bottle to the label
the edges can be cut out in waves
adjust the lower part of the bottle in height and cut off the excess
make a large hole - input
remove the cuts with a hot knife so that they are not too sharp
color the workpieces with bright colors
on the sides of each blank make symmetrical punctures with a hot nail
put on the top of the bottle on the base so that the holes match
pass the twine and tie the nodules inside the lower part of the feeder
make a hole in the bottle lid
pass through it the nodules of the twine and pull
on both sides of the window, connect the roofs and the base of the feeder for additional fastening
decorate the feeder with bowing or buttons with hot glue

With a bowl

You will need:

1-2 liter
deep plastic plate
bolt with a nut
beautiful tape or tourniquet

Production process:

in the center of the plate and the cover from the bottle, make a hole
fight them together with a bolt and nut
pierce a few holes for feeding a feed for feeding the bottle
in the lower part of the bottle, make the holes through which extend the tape
pour the grain into the bottle
twist a lid with a plate
turn over and hang behind the tape

From several bottles

Prepare:

1 bottle of 2 liter
4 bottles of 1 - 1.5 l
wire

How to do:

take a large bottle and mark, retreating from the bottom about 7 - 8 cm
make holes on four sides, the diameter of which should be slightly smaller than the width of the neck of the smaller bottles
cut the top in small bottles so that one side of the resulting funnels is a little elongated
insert the neck of the funnels into the holes of the large bottle
turn them down the long side - we got comfortable birds for birds
in the upper part of the large bottle, take the wire
form a loop
fill the feeder with food
twist the lid and hang on the branch

From vinyl records:

Materials:

a bottle of 2 liter
two old records
twine
hot glue

Production:

put the plate on an iron pan
put in a hot oven for 3 minutes
give a softened plate the shape of a bowl (you need to work in protective gloves!)
in the center, make a hole in the diameter of the cover from the bottle - this workpiece will serve as a roof of the feeder
make a bowl of the second plate in the same way, but without a hole - this will be the basis of the feeder
while the hot is hot, make 4 holes at the edges of the plates, into which the twine will take place
at the very bottom of the bottle, pierce the holes for feeding food - it turned out to be a bunker for food
glue the vinyl “plates” with hot glue to the bottle (holes in both plates should be located above the other)
pass the twine through them and hang in a suitable place

How to make an original winter feeder for birds from plastic bottles?

Did you know that more than half of the birds in our latitudes do not live until spring? They die of hunger. We can help birds to survive the cold, we feed them.

The “correct” winter bird feeder must meet the following requirements:

have a roof, thanks to which snow will not fall asleep for feathers
the walls should be high enough so that the strong wind does not blow the food out
the fastening should be good, since gusts of wind can tear the product from the tree
be made of dense material not afraid of low temperatures and moisture

We will tell you how to make a practical winter feeder.

Method 1:

prepare 1 bottle with a volume of 5 liters and 2 bottles of 1.5 liters
on the three sides of the large eggplant, mix places for the windows: one large and two smaller
make the slots in the form of an inverted letter p
bend the cut parts up like visors - the base of the feeder turned out
in one small bottle, pierce the holes in the bottom and a little above it
insert this container into the cups - bases
make a hole in the lid of a large bottle through which the inner bottle can pass the throat
twist the cover on the eggplant. In this case, the neck of the inserted container should rise above the lid
cut the upper part from the second small bottle
cut a neck with her
the resulting funnel put on the neck of the inner bottle
pour the feed and tighten the lid

Method 2:

you will need a bottle of 1-1.5 liter and an old plastic container with a lid
in the center of the lid from the container, make a hole in size, a little smaller than the size of the bottle neck
on the sides on the lid from the container, cut large windows - bird entrances
in the lid of the bottle, break the hole through which the feed will be served
pour the food into the bottle
twist the lid
insert the bottle into the lid hole from the container
close the container with the resulting design
make a bech or wire mount

Method 3:

take 3 five -liter cups
make large holes in them - the entrances on one side
pour the contours with electrical tape
using bolts and screws, connect the bottles with each other so that bird windows come out
below the bottles make holes and insert sticks - poles
having wrapped an eggplant with a wire or rope, make a loop mount
a very spacious feeder for a large number of birds turned out

How to decorate the craft of birds from plastic bottles?

A bird feeder can become a real decoration of the garden or window, if you show imagination and make some efforts. Bring children to this process. This lesson will not only contribute to the development of their skills, but also teach to be merciful to our smaller brothers.

You can decorate a plastic feeder using various methods:

painted with colored colors
make vinyl applications
wrap it with twine lubricated by PVA glue

stick on top natural materials: cones, rowan berries, dry leaves, spruce branches
fastening to make a curly curved wire
paste with round parts of plastic spoon

However, do not forget that the main thing in the feeder is still not design, but timely filling with food.