Instructions for cleaning the cooler at home.
Content
Water cooler is a simple device that is used to heat or supply chilled water in offices and houses. Many of the inhabitants of large cities are accustomed to such a miracle of technology and are great about the fact that it is always at hand clean, as well as hot water from which you can prepare tea or coffee. In this article, we will consider how to clean the cooler.
How to clean the water cooler yourself with citric acid: Instruction
Everything is quite simple. It is best to clean the moment when you are going to replace the bottle with a new one. That is, the previous one remained empty. In this case, you will not overspery clean water, but will perform procedures without it.
Instructions:
- It is necessary to remove the old empty bottle and turn off the device from the mains so that there is no heating
- Wait 5-6 hours so that the water in the compartment with hot water is completely cooled and you do not scald
- Now completely drain the entire liquid through the taps. To do this, take a bucket or any receiver
- Please note that this is not all the liquid that is in the device
- There are special holes from behind him, in which there are plugs. Be sure to remove them and drain the remnants of the liquid
- It is there that old water accumulates. After that, unscrew the taps, and immerse them in a solution with soapy water, wait a bit
- After that, take a brush for washing dishes and rinse the taps thoroughly, rinse it with clean water
- Next, it is necessary to clean the tank in which water is heated. It can be very clogged, and most often
- Despite the fact that the water in the bottles is cleaned, the scale is still formed
- In order to remove it, it is necessary to use citric acid. The technology is very similar to cleaning the washing machine
- It is necessary to dissolve a citric of citric acid weighing 100 g in 5 l of water, mix until crystals dissolve
- It is necessary to pour the entire liquid into the tank into which a new bottle is inserted
- Please note that the capacity of these tanks in each model is different. It may not be 5, but 4 liters. Therefore, the cleaning solution may remain
- Now connect the device to the mains and turn on the heating. Wait for the device to turn off, and the water will completely warm up
- Wait a little and drain the water. It is desirable that the liquid stays in the tank for about five to six hours. Now gently drain the liquid from the tap of hot and cold water
- After that, it is necessary to flush with four liters of pure water and without adding citric acid
- This kind of manipulation will get rid of old, bacterial deposits, as well as lime
Please note that after delivering bottles to your home, and installing the new to the cooler, it is necessary to carefully remove the film and wipe the neck with a damp cloth or alcohol solution. This is necessary in order to remove bacteria and dust that settled on a bottle during transportation. If you do not, then all dust, microorganisms will enter the cooler, and accordingly into your body while drinking water.
When is the cooler processing?
Cleaning must be carried out about once a month. If this is not done, then bacteria will multiply in the cooler, as well as to grow scale. Which over time can lead to a breakdown of cooler or to the appearance of an unpleasant smell of mold or rotting water. This is all due to the fact that untimely cleaning of the device is carried out or its ignoring.
Do not forget to wipe the device outside, dust accumulates on it. In addition, remove the capbleder, which is located from the bottom of the mesh, and rinse it with a small amount of dishwasher. Wash the surface, which is located under the capbleder.
As indicated above, preventive cleaning is carried out once a month, but some ignore the rules. Be sure to observe how the device works.
Signs of the need for cleaning:
- Water does not flow or the stream is very thin, so the liquid flows extremely slowly
- The cooler constantly overheats, turns off
- The tank is constantly very hot water, or the water does not heat up at all
- There is an unpleasant odor from the water, as well as a specific taste
All these signs indicate that the cooler is clogged, bacteria multiplied in it harmful to the human body. Therefore, it is necessary to clean the urgent order. If you do not know how to do it, or are afraid to clean the equipment, contact specialists who are engaged in adjusting and servicing the cooler.
How to clean the cooler guangpolisept: instruction
Another option for cleaning is the use of a special solution called guangpolisept. This is an antiseptic based on polymers, which does not contain harmful impurities, heavy metals, as well as chlorine. Therefore, it is absolutely harmless to the body.
- It is divorced in the amount indicated in the instructions and is also poured into the cooler tank, washed.
- Please note that such cleaning is carried out within a day. That is, from time to time it is necessary to open the taps and drain the water.
The tool belongs to the new generation disinfectants (polymer guanidine antiseptic drugs), not containing active chlorine, aldehydes and is produced in the form of 15% of the aqueous solution, which is a transparent colorless fluid without odor, with unlimited solubility in water.
Cleaning cooler is a simple manipulation that will remove all organic and inorganic formations inside the tank with water. This will extend the service life of the apparatus and will prevent the reproduction of pathogens.
Video: Cleaning Coler
