How to make linoleum seam invisible? How to properly glue linoleum joint in the joint step by step: instruction

Three methods of connecting two linoleum canvases: installation of a rock, cold welding and hot welding.

If you are puzzled, how to connect the seams of linoleum at home, then you need to choose one of three technologies. We will talk about each of them in detail.

• Connection of two linoleum canvases using special rocks. This method is very often used when you need to connect two linoleum canvases between neighboring rooms. The threshold will be visible, but if it is between the rooms, then this is not quite bad, because the space should be visually delimited. For work, only a purchased pigeon and a drill will be needed.
• Cold welding of linoleum. It is often used when you need to unnoticed two canvases inside the same room. We need special glue and skillful hands.
• Linoleum hot welding method. Reliable and expensive, we need special tools. As a rule, it is used in public premises, where high wear resistance is important. If you think how to hide the seams of linoleum and achieve perfect adhesion of materials is a method for you.

How to combine two pieces of linoleum with a thorough?

Do you think how to connect the seams of linoleum at home? Using a special threshold is the easiest and not very laborious option. In the store, you will most likely find thresholds of aluminum and PVC thresholds.

IMPORTANT: We recommend that you use aluminum rapids to connect the seams of linoleum. They are strong and durable. PVC spikes cannot be reliably pressed against linoleum, dirt and water will fall under it. In addition, it is short -lived, and after a few years of operation, cracks.

Aluminum rapids have a special shape, when you fasten them with self -tapping screws in the center, the edges are reliably and tightly pressed by pieces of linoleum that you connect.

• How to connect the seams of linoleum at home with a vote, step -by -step instructions:

1. The first, and one of the most important stages of repair robot is preparation for these very works. Make sure you are doing everything in the correct sequence. Mount the threshold before you installed the door frame and you can’t put the platbands! He will interfere. Also make sure you put linoleum evenly.
2. We accurately measure the required length of the rock and cut off the excess scissors for the metal. The threshold should “walk” a little, that is, there is less than the door frame for 1-2 mm. This is necessary so as not to scratch the door frame.
3. We drill the floor with a drill to insert dowels into it and insert them there. You need to drill, as for other repair robot, first, we first take a smaller drill than required, then gradually expand the hole. If the drill in normal mode can drill your black floor, do not use the expansion mode. Treat the screed as carefully as possible so that the threshold holds well.

Video: How to install a regular threshold for linoleum between rooms

INTERESTING: Aluminum rapids are simply colored or with a decorative film. For example, if you have a linoleum under a light tree, then you can choose a golden sheed or a spike with a pattern that imitates a tree. It is better to combine linoleum with a sprout without a decorative film, because it inevitably erases over time.

How to connect the seams of linoleum at home, if a warm floor or soft screed below

Quite often it happens that it is impossible to put the threshold by the usual method, having driven into the floor of the dowel. There may be a lot of reasons for this: pipes of a warm floor pass below, and you are afraid to get into them, you insulated the floor with expanded clay or other loose material, and no dowels are kept in it, you have a crack between the concrete slabs just under the doorway and you are afraid that over time it can expand.

So, how to connect the seams of linoleum at home, if you can’t drill the floor? It remains only to glue the threshold! The author of the next video claims that for this you need to use a sealantor silicone glue, but not “liquid nails”.

Video: How to glue the threshold to the floor?

If you think how to connect the seams of linoleum at home, our step -by -step instruction for you:

1. We measure the required length of the rock and cut it to the desired size.
2. Carefully degrease all surfaces, for example, a solvent or varnish for removing varnish. It is important! After all, we will use the sealant, and it holds well only on smooth and well -solid surfaces.
3. We put the threshold so that it lay evenly, and draw a felt -tip pen or soft pencil along its edges. Then we remove the threshold.
4. We take the masking tape and glue it clearly to our lines. We smell the edges well.
5. In large drops, we apply silicone sealant on the floor and on the threshold. There should be a lot of silicone. He must directly get out after you press the threshold.
6. We attach the threshold, press it tightly. Then we remove the painting tape with the remains of silicone.
7. After a day, the silicone will freeze, and our threshold will be very firmly glued.

ADVICE: To make your gender look aesthetically pleasing, try to ensure that the threshold is exactly under the door when it is closed.

How to make linoleum seam invisible: cold welding for linoleum

If you can’t do with one whole piece of linoleum, and you think about how the seam of linoleum is inconspicuous, then the next technology is for you.

This method will be useful if the room is too large, and linoleum is only narrow, or the room has the wrong shape. He will help out when you or the seller in the store were mistaken, cutting off linoleum, and you need to add a piece. Good, cold welding for linoleum And accuracy help to make the seam almost invisible.

Do you think how to glue linoleum to linoleum at the joints? Glue for cold welding of linoleum is suitable as possible, it can be three types, which are designated by the letters A, T and S.

• Type a Suitable for a new, just laid linoleum. The tube is equipped with a tip with a needle at the end. And the glue itself provides a very strong fixation. This glue is not suitable for linoleum with a soft felt substrate.
• Glue type t Used for linoleum with felt insulation, freezing it remains flexible. The tube of such glue is supplemented by the tip in the form of the letter T.
• Glue type s Used for old linoleum. It is suitable if the linoleum panels began to diverge over time. It has a structure resembling a gel, and not as liquid as glue such as A. spreading along the crack, it is able to connect the canvases that are from each other at a distance of 0.5 cm.

We will consider in detail how to make the seam of linoleum inconspicuous, with the help of glue like A.

1. Linoleum needs to be spread evenly around the room and make it lay down. Experts believe that linoleum, which was only spread out of the roll and cut along the edges, should lie in this state for a day. For a very thin linoleum, 6-8 hours can be enough. In this case, the floor on which linoleum is laid is by no means wet. And the room should be warm and without drafts.
2. Two panels that we will connect the joint in the joint should initially intercede one another by 5 cm or slightly more.
3. When linoleum is neatly laid out and put out, you need to take a good, heavy construction rule of a trapezoid, like the one that is in the figure below. And tightly press it to the place where linoleum is overlapping.

4. Clean the rule tightly to linoleum, and cut two canvases at once with a knife. It is more convenient to cut on the other side of the rule that is not mowed. Try to keep the knife strictly at right anglesTo make the edge of the material even, without bevels.

5. When the canvases are cut, we remove two extra strips.

6. Masters who perform work in this master class offer to use two methods for reliability to glue linoleum to linoleum at the joints, cold welding and double-sided tape.

To glue the adhesive tape, one of the glued paintings is slightly rolled up, and along the edge of the second, a line is drawn with a pencil on the floor. Then the second canvas is rolled up. After that, we glue a double -sided tape to the floor so that the drawn line falls in the middle of the adhesive strip.

Double -sided tape should be glued slowly, unwinding a roll of 40 centimeters, and then smoothing and leveling tape.

7. The upper protective film is removed from the adhesive tape, and linoleum canvases are placed in place. They already look quite aesthetically pleasing. But we want to achieve good wear resistance, so this is not enough.

8. We take the masking tape and glue it on the connected linoleum canvases so that the joint turns out in the middle of the painting tape.

9. In our case, in the question of how to glue linoleum to linoleum at the joints, the best answer is a cold welding for linoleum like A. Since our linoleum is new and the gap is very small. We put a needle on a tube with glue, and straighten the painting tape straight with a needle, gradually pressing the tube. Do not spare cold welding, it should directly protrude from the crack! It is also important to insert a needle deep enough!

ADVICE: Do not cut the masking tape with a knife, this is the likelihood of damaging linoleum. Cut the adhesive tape with the very needle on a tube with glue, most likely it will cope with this task.

10. 10 minutes after applying the glue, masking tape can be removed. And after a day, the glue will completely dry and the joint will be ready!

Video: How to connect two linoleum canvases in the joint using the Cold welding glue?

How to properly glue linoleum joint in the joint: instructions for the method of hot welding

Hot welding of linoleum is a professional industrial method. It is high -quality, reliable and expensive. If you need to figure out how to hide the seams of linoleum, for example, on the floor of the gym or a shopping center, the hot welding method will be very useful. With it, you can make beauty, like the one in the photo below. And this floor will be durable.

For work, special tools will be needed: a hairdryer for hot welding of linoleum, it is in the photo below, and a special cutter, with the help of which a groove is cut out at the joints of linoleum.

Full, a set of tools for those who think how to properly glue linoleum joint in the joint, in the photo below. It includes:

• Industrial dryer
• Standard nozzle on it
• A cord welding nozzle, which is dressed on top of the first nozzle
• Groove knife
• Crescent knife with a nozzle on him

How to properly glue linoleum joint in the joint: Instructions.

1. First, you need to take a knife to put the seam and cut a semicircular groove for them, where you have two linoleum panels. A molten cord will be invested in this groove.
2. We take a hairdryer and first we put on a regular nozzle on it, and then on top of it a special nozzle for hot welding of linoleum.
3. We insert the cord into the device. A special hot welding cord is sold in construction stores in bays.
4. Then you need to cut off the protruding part of the material. It is necessary to trim it in two stages: first a sickle knife, on which the nozzle is worn, and then just a sickle knife.

Equipment for hot welding of linoleum can be different, in our next video, you will see professional equipment to perform these works.

Video: hot welding of linoleum

Perhaps you will be interested in our other articles:

• How and what to align the floor to put linoleum?
• How to wash a laminate?
• Which is better laminate or linoleum?
• How to stick wallpaper correctly?
• How to wash linoleum after repair?