How to make a large, small palm tree and palm-bonsi from plastic bottles? Step -by -step instructions for assembling palm trees from plastic bottles

In this article, we want to talk about how to successfully combine love for tropics, creative and unnecessary plastic bottles.

Content

Palma is an undeniable symbol of summer and rest. But I want to get to live palm trees, and I would like to buy a piece of such a wonderful sunny mood. However, why buy a palm tree if you can make it with your own hands? Yes, and using objects that are easy to find in any house are plastic bottles.

How to make a palm tree from plastic bottles in stages?

Let's start by cutting the palm leaves. To do this, divide the plastic green bottle into two parts, the upper

For palm leaves, the top of the plastic bottle is taken

Now the strips are cut into this upper part. Process the surface along. The shape of the bottle does not matter - any

For palm trees from plastic bottles, the strips are cut along the bottle

After cutting the resulting bottles They are fixed on the cable

Important: the diameter of the cable should be from 12 to 14 millimeters.

Palma leaves from the bottles are connected to the cable

And such blanks for palm leaves from bottles should be several

And now you can start making the barrel. Plastic bottles of about 2.5 liters of brown color are useful for them

These bottles are useful for making a palm barrel from a bottle

Along the bottles Make incisions so that the strips are wide

For a palm tree made of plastic bottles on a bottle for the barrel, you need to make cuts

The bottom is cleaned

The bottom is cut out of plastic bottles from the bottle

Prepare a metal sheet, whose thickness should be more than 0.5 centimeters. Two rods need to be welded to this sheet about 25 centimeters long. One of them should be at an angle of 90 degrees to the sheet, and the other is less

For the manufacture of palm trees, you will need a metal layer

On the rods, plant metal tubes. The diameter is desirable in the range of 20 millimeters. As for the height, it depends on how much the palm height you want to see

At the ends of the rods, you need to weld metal sleeves. It is in them that palm leaves from bottles will be planted

Fastening of leaves on a palm tree from bottles

Important: the wires on which impromptu leaves are planted are better to bend.

The wires on which the palm leaves are held from the bottles, it is better to bend

As soon as the leaves were collected you can start the barrel

As a result, such palm trees will be obtained

Palma scheme from plastic bottles

For clarity, you can see on the diagram how to form the trunk of the future tree made of plastic bottles. Fasten an iron rod in the ground, and then string the bottles on it. Pre -cut the bottom from the bottles

Creating a palm trunk from plastic bottles

In green bottles intended for leaves, the bottom is also cut off. Further each of the bottles is cut into 3 or 4 parts. Each part, in turn, is made out in the form of fringe

Flying foliage forming scheme from bottles

As soon as a few green bottles are decorated in such a way as indicated in the diagram, You can start assembling the crown

Important: it is recommended to make cuts in the form of crosses on a brown bottle - so green bottles will be better attached. For better fastening, you can also fasten with each other with wire composite crowns inside a brown bottle.

Palma crown design scheme from plastic bottles

Now the top with the crown is attached to the barrel as shown in the diagram

Crohn mounting scheme to the palm barrel from bottles

How many plastic bottles do you need for crafts?

There are plastic bottles in every house, but how many do they need for palm trees? For the barrel Save 10-15 pieces of brown material, or even more.

Pay attention to the lotrazh: So, for a craft of 15 bottles, it is recommended to purchase a two -liter material, but for smaller palm trees - of 10 bottles - you can stock up on one and a half liter bottles.

As for the leaves, then it is better to take more bottles for them - palm leaves are quite long. On average, for one palm, you need at least 7 bottles.

Both brown and green bottles are useful for palm trees from bottles

How to make palm leaves from plastic bottles?

If you want to get wide leavesReminding me, cut the bottom first. Then make cuts in the bottle so that three parts form. It is recommended to use not only green bottles, but also yellow - so the palm tree will look more natural

Important: bring the cuts about half a fellow to the neck.

Each of the cuts is rounded and narrowed to the base Thus, to resemble leaves
Now you need bend all the leaves outward
The leaves are cut in such a way that the fringe is obtained. The fringe is necessary on both sides of each leaf. The middle, of course, should remain untouched - 1.5 centimeters enough. It is recommended to bent each clove according to the following principle to create splendor - one down, the second is exactly, and the third is up

Such should be the leaves with a fringe of a palm tree from plastic bottles

How to make a palm barrel made of plastic bottles?

First of all, cut about 1/3 bottles - Namely the bottom
8 petals are cut out of the remaining bottle. From the lid you need to retreat half a pack
Turn out each of the segments

Important: you can also use the cut third of the bottle to save material. However, you will have to make a hole in it for this. You can use a knife previously displayed on the stove for such purposes.

How to assemble a palm tree from plastic bottles?

As a rod, which will serve as a support for a palm tree, it is best to use a metal -plastic pipe. Its diameter should be 20 millimeters. But there are no restrictions on the height.

Start assembly from below. Moreover, for the bottom, select the largest details, for the top - the smallest. They are assembled by the "glass in a glass" method
The petals at this time should turn In a checkerboard pattern
The very bottom is best attached with double narrow adhesive tape - It is perfectly connecting. However, you can use glue
But 30 centimeters to the top of the rod, you need to finish collecting the barrel and start collecting foliage. And use the chess order too
As soon as the assembly ended, brease the reinforcement for 30 centimeters in the ground. At the same time, 40 centimeters should remain on the surface. And now put on this reinforcement a ready -made pipe with a palm tree

This is how a palm is obtained from bottles

Palm Palm options

Palms made of plastic bottles can look different. But it is better to see once, so we bring to your attention a selection of photos With similar artificial trees.

Palms from plastic bottles with a flat trunk

Palma made of plastic bottles with a barrel-bell

Palmes made of plastic bottles with non -bore sprawling leaves

Palma from plastic bottles with a thick thorough barrel

Palma from plastic bottles with a high barrel

Palms made of plastic bottles that are not stylized for real trees

Palma-Bonsai from plastic bottles

For the manufacture of such a palm tree cut the top and bottom in the bottle

In a bottle for palm-bonsi from plastic bottles, you need to cut off the top and bottom

From the resulting green plastic material cut small strips, and from them are leaflets

Important: the strips should be about a centimeter in width.

Palm-bonsi leaflets from a plastic bottle

Each of the pieces of leaflets is necessary pierce

On each leaf for palm-bonse from a plastic bottle, holes are made

You should also prepare a wire for branches - it should be from 0.2 to 0.5 millimeters in diameter

Palm-bonsi tones wire from a plastic bottle

Now cut 30-50 centimeters of wire And fold it in half. Pass the first sheet and twist the ends 2 or 3 times - this is how it is fixed

So the leaflets for palm-bonsi from a plastic bottle are attached

The first rectangle is the upper leaf. Place the rest on both sides of it

Fix the leaflets on both sides of the upper one in the palm-bonsi from a plastic bottle

Important: to retreat from each pair of leaves should be 3-4 millimeters, and then you need to twist the wire.

As soon as the weaving of the twig ends, twist the ends. In general, you need to stock up on the palm tree with 15 twigs. Let the upper ones contain the largest number of leaves, and the lower ones are less

Upon completion of the branch of the Bonsai palm from the plastic bottle, it should be twisted

The palm tree will be made of two tiers. The branches should be intertwined, creating a common barrel

Weaves of branches into the barrel of the palm-bonsi from a plastic bottle

And now we will create the foundation. The pot is not very suitable - it is best to fix the palm on the island. For its manufacture, a soap dish, a saucer, a ship - anything that has an oblong shape is useful. The capacity is covered with a dietary film, and then filled with a liquid alabastr

For an island for a plastic bottle palm, a ship is suitable

Put the palm in a ship and wait 10 minutes - During this time, hardening will occur. Then it will only remain take out the platform with a tree from a container

Palm-Bonsai Palma Palm Palm Plastic Plac

It only remains colorn the island as you want

Palm-bonsi island ash-painting from a plastic bottle — Coloring the island for palm-bonsi from a plastic bottle

How to make a large palm tree made of plastic bottles?

First of all, stock up on a large number of bottles. Cut them in half, and form the teeth on parts of the cut
Further in the ground the metal pin is attached. You can use solid wire as an alternative

Important: be sure to take care that the pin is firmly attached to the ground.

Processing blanks stroke on the pin. It is advisable to go around them in order to create a natural effect
From green bottles cut the leaves, after removing the bottom from the bottles
Combine all elements in the overall structure. They can be striking with tans or welding

This is how a large palm is obtained from plastic bottles

How to make a small palm tree made of plastic bottles?

For such a small palm for a room you will need it Only 3 brown bottles and one for leaves with a capacity of 0.6 liters.

So, cut each of the brown bottles into 4 equal parts. And by the cut of each part you need to form incisions in the form of triangles in a centimeter
Bend these slices
Now divide the green bottle into 3 parts, the largest of which will be the one with the neck - 9 centimeters
Collect the barrel from the part that consists of the bottom. Pushing other components of the trunk into it

Important: it is recommended to use glue, which is universal - it interacts well with plastic and has no unpleasant odor.

As you can see, you can arrange your own tropics in any lane of our immense homeland, and at any time of the year. The material is very affordable, and it will spend a little time. In addition, such a palm tree is perfect for those who do not have time to care for living plants.