How to remove measurements from a female figure? How to measure the width of the back, shoulders, the depth of the arm of the sleeve, half the waist and girth of the waist, shoulder, chest, neck, hands, hips, knees, legs, ankles, shoulder length, sleeve, back, legs on the outer and inside of women?

From the article you will learn how to make measurements correctly to sew a blouse, dress, skirt or trousers on a female figure.

Content

Even a novice dressmaker knows that, sewing the simplest thing, you need to start with the correct removal of measures. If you skip this step, then it is likely that the finished product will not correspond to the required size.

If you want to avoid such a problem, then be sure to sew a blouse, dress or trousers before sewing, remove all the necessary measurements. About how to do this correctly and tell our article.

How to remove measurements from a female figure: General recommendations

Recommendations that will help you correctly remove the measurements from the human figure

As you already, probably, understood the removal of measures to be approached as responsibly as possible. That is why, before you start doing this, you need to ask a person to undress to the laundry. Especially this rule is relevant in the autumn-winter period, when women wear more voluminous clothes, which will add additional millimeters to the received measurements.

Many beginner needlewomen do not take this nuance and, as a result, after sewing, the clothes are sitting differently as it should. Another important nuance, which must always be remembered, is modern tightening tights. If you sew a tight dress or skirt, then consider that this female accessory is able to reduce volumes by 1-3 centimeters.

Other recommendations that will help you correctly remove the measurements from the human figure:

Become as directly as possible and in no case do not stoop
With all this, try that the body is not very tense
When removing the length of the product, monitor the legs are not even bent at the knees a little bit
Applying a sewing meter to the body in no case do not pull it
He must freely fit the body, but at the same time do not sag
Measurements must be carried out at the most protruding points of the figure
Try to tie the waist with an ordinary base, and only then measure all the lines associated with the waist area
Make sure that a person from whom the measurements does not inflate and does not blow his stomach

How to measure the width, the length of the female back to the waist: description, diagram

We measure the width of the back:

Ask a person to become as correct as possible
It should become so that you can see the protruding parts of its shoulder blades well
Take a sewing meter and attach it exactly horizontally with respect to the waist line
A meter is applied to the upper corners of the axillary depressions

Important: in no case do not add even a few millimeters to the result obtained as in the end you can get too small the wrapper of the product.

Measure the length of the back to the waist

Before starting to shoot this measure, be sure to tie a box or any tape on the waist (the main thing is that it does not slip and holds well on the body)
Ask a woman to become straight and start measurements
Attach the sewing meter to the protruding vertebra and precisely lower the ridge to the waist line
Where a meter will stop with a bark and there will be an exact indicator of the back length

How to remove measurements from women's shoulders - width, length, shoulder girth?

The width of the shoulders is measured quite simply. All you need to do is find the two most extreme points of the shoulder joints and correctly apply the sewing tape. They are located in a place where our shoulders smoothly begin to turn into their hands. So, attach the sewing tape on the right shoulder joint and draw a direct horizontal line from it to the left.

If you need to measure the length of one shoulder, then also attach the edge of the measured tape on the shoulder joint, but in this case, draw a straight line to the beginning of the base of the neck.

As for the girth of the shoulder, it must be measured at the widest point of the hand, as close as possible to the shoulder joint. To do this, attach the tape to the hand (strictly horizontally) in the armpit area and click it into the circle. The result obtained and will be a girth of the shoulder

How to remove a woman's standing height, half -wrapping her breasts?

Measurement of height, half -wrapping a chest

Important: when measuring this parameter, a bra should be dressed on a woman who will not push the breasts. And this means that he should simply support the chest in the correct position, not very much raising it up.

In order to measure the height of the female breast, you will need to attach a measured tape to the point where the neck begins to go into the shoulders and lower it horizontally to the very protruding point of the chest. Try to arrange it in such a way that it sinks as much as possible on all rounded bends, and does not leave anywhere. If you need to measure the half -cake of the chest, then just attach the tape strictly horizontally around the body and at the same time make sure that it passes through the most protruding points of the chest.

How to measure the length of the gear of the female figure to the waist: description, scheme

In order to correctly remove this measurement, you can use the method that we told you about at the very beginning of our article. It will be better if you initially indicate the waist line with a bike and only then proceed to the measurement of the gear. Thus, you will be able to get the most accurate result the first time, and you can not worry that the measurement is not entirely removed correctly.

In order to get the correct result, attach the tape to the point at the base of the neck and draw a horizontal line along the most protruding point of the chest. The tape should freely lie down in the figure and in a horizontal position to drop to the waist.

How to measure the girth, half -chatting a female waist?

Even a novice seamstress will be able to measure the girth of a female waist without any problems. All that will need to be done for this, visually determine the narrowest part of the female figure and attach a measured tape to this place. She should lie tightly on the waist, but not to squeeze her. In order to get half a waist of the waist, the result must be divided by 2.

Important: in this case, the rule of the “relaxed abdomen” acts, this means that in no case it should be “inflated” or retracted.

How to remove measurements of heights, depths, widths, circles of the armhole of the sleeve from behind and in front for a female pattern?

Measurement of height, depth, width, circles of the armor of the sleeve

The circumference of the arm of the sleeve is measured in the shoulder joint. To remove this measurement, attach a measured tape to the highest point of the axillary cavity, and then skip it at hand, and heated the entire shoulder joint. Do not rush to record the result right away.

Ask a person to straighten his hand or simply move it. Such a small trick will contribute to the fact that the measured tape will slightly disperse and as a result you will receive the most accurate indicators. How to correctly determine the depth and width of the armhole of the sleeve, you can see in the picture posted slightly higher.

How to measure the girth and half -grab of female hips?

The girth and half -grab of the hips is measured in the same way as the measurements from the waist area. You will need to arrange a measured tape exactly horizontally in the hips. Be sure to ensure that it is located at the most protruding points of the buttocks. Also, in this case, it is necessary to take into account the presence of a protruding tummy.

Women with the “Galife effect” must be carried out additional relief. In this case, the tape is located just below the buttocks, but at the same time it is necessarily placed at the protruding points of the "Galife". The hip half -wrapping indicators can be obtained by dividing the results obtained by 2.

How to measure the girth of a female neck?

Important: when removing this measurement, it is very important to consider the presence of fat deposits in the neck and the presence of a second chin. All these nuances will subsequently affect the formation of the width and depth of the future product.

So, pick up the measured tape and place a slightly above the point of connection of the neck and shoulder. Wrap the tape around the neck, trying to keep it anywhere to squeeze the skin, but at the same time does not hang out. Be sure to make sure that it lies exactly horizontally and fix the result.

How to measure the girth of a female hand?

When removing measures for a hand, it is important to consider a thing with a long or meek sleeve you will sew. If it is a blouse or a short sleeve T -shirt, then you will need to measure the girth of the widest part of the hand. If you plan to sew a business blouse or a long sleeve shirt, you will have to duplicate the measurement in the wrist.

To remove the measures in the upper part of the hand, place the measured tape on the external area of \u200b\u200bthe axillary cavity, and click around the hand. Write down the result. Next, we go to the second measurement. In this case, we have a tape in the wrist joint. It should be located precisely horizontally and tightly fit the hand.

How to measure the length of the sleeve for a woman?

Important: needlewomen with experience most often measure the length of the sleeve simply with a tape, to a relaxed hand, which is lowered in parallel to the body. If you are going to sew your first blouse, then remove the measurement from the hand slightly bent at the elbow. So you can guess with the size and, as a result, the sleeves of the finished thing will definitely not be short.

This parameter is measured by applying the sewing tape to the very extreme point of the shoulder slope and to the desired length of the sleeve. The maximum length is removed to a point 1 cm below the wrist. If you remove the measurements for a short sleeve, then you can not bend your hand, but place it in the correct physiological position.

How to measure the girth of a female knee?

There are two ways to measure the girth of a female knee. Both of them have the right to exist, but still, as practice shows, the second gives a more accurate result.

The first way. Stand straight and attach a measured tape in a horizontal position exactly in the middle of the knee cup. Close it around the knee joint and fix the result.
The second method. Bend the leg at the knee so that the angle of 90 degrees forms. After that, attach the tape in the same way as in the first case, and look at the result.

How to measure the girth of women's lower leg and ankles?

Most often, this indicator is removed for sewing female leggings or narrowed jeans and trousers. In view of this, when removing these measures, it is extremely important not to apply a measured tape very tightly to the leg. If you transfer the lower leg or ankle, then in the end, after sewing, the thing will strongly squeeze the above places, and visually it will not look very harmonious.

The girth of the lower leg and ankles is measured in the same way. You will need to arrange a measured tape in a horizontal position along the ankle or exactly in the middle of the lower leg, close it into a not too dense ring and see what result was obtained.

How to remove measurements from the feet from the external and inside of women?

The length of the leg from the outer and inside

Important: when removing these measures, be extremely careful. The difference between the results obtained in the future will be used in the construction of trousers. This indicator will indicate what height of the seat they will have. If you remove the measurements not quite correctly, then the trousers can be either too small or too deep.

In order to correctly remove the measurements from the outside of the leg, to start, tie a box or ordinary tape on the woman’s belt, thus indicating the waist line. Next, ask a person to stand straight, attach a measured tape to the waist and lower it on the thigh.

It is desirable to lower the tape to the floor, especially if the subsequent thing will be worn with high -heeled shoes. On the inside of the thigh, the measurements are removed in a similar way, just in this case the tape is applied to the very top of the leg at the groin and drops to the required length.

How to measure the length of women's clothing on the back?

The length of the female product on the back

If you are interested in this particular parameter, then remember that it is necessary to remove it from a person who stands as directly as possible. If it deviates from the vertical axis, then the result will turn out not entirely correct. Especially if you sew a shortened version of a blouse, jacket or jacket.

The length of the female product is measured on the back from the lowest point of the base of the neck and to the required length of the product. If you sew the product long to the waist, then be sure to use the method with the ties of the box on the narrowest section of the figure. We mentioned it at the very beginning of our article.

How to measure the length of women's trousers?

Even needlewomen with experience do not dare to sew their own pants for a long time. And the thing is that in this case it is necessary to remove quite a lot of different measures. But still, if you correctly decide on the volume of the waist and the girth of the lower leg, hips and ankles, then it will be possible to sew such a thing the first time.

We have already told how to determine all these parameters above, so now we will clarify how to measure the length of the trousers. In order to get the estimated length of the trousers, you will need to apply a measured tape on the outer side of the thigh. The tape is attached to the waist line and drops to the floor. The result obtained will be a long finished product.