How to clean and bleach a bath at home with soda, peroxide, citric acid? How to bleach an enameled, acrylic and cast -iron bath?

Ways to clean the bathroom from rust, lime plaque and yellowness.

Content

A clean bathroom is an indicator of the cleanliness of the mistress of the house. This is one of the most frequently visited places where a lot of mold, dust and soap plaque accumulate. In places of contact of the bathroom with a mixer or drain, rust and scale are often formed.

How to clean a bath from rust?

Rust is often eaten into the surface of a metal bathroom and it is difficult to remove it. Many housewives solve this issue by acquiring expensive cleaning tools. But, unfortunately, they, too, do not always cope with the problem perfectly.

The instructions for cleaning the bathroom:

Take a jar of glass and rinse it. Remove moisture and pour 100 ml of ammonia
Add 50 ml of hydrogen peroxide to the substance and stir
Soak the fabric with a composition and rub the pollution
You can pour part of the solution on the rust and leave for 20 minutes
Wash off with warm water, repeat if necessary

Rust - iron oxide, which is removed using acids and alkalis. It is perfectly dissolved with ammonia, vinegar and special aggressive means.

How to bleach a bath from yellowness?

Many housewives regularly use this method to clean the shells and bathroom. The effect of the method is based on the use of wine vinegar and salt.

Instructions for the excretion of yellowness:

Mix 100 ml of wine vinegar and 50 g salt in a glass vessel
Put the dish in the microwave and heat the solution to a temperature of 70 ° C
Moisten the fabric with liquid and rub the contaminated places. Leave for 30 minutes
Do not overexpose the solution, as it can damage the enamel

How to bleach an enameled bath?

Such products are best cleaned with acid -containing solutions. To make the product perfectly, it is necessary to warm up the bathroom. Just pick hot water into it, lower it and wipe it dry.

Only after that apply a cleaning product. Emall should not be rubbed with abrasives and a metal scraper. From this it can be covered with cracks. In these cracks, dirt and mold are often clogged.

Emalie whitening instructions:

Heat the product. This enhances the chemical reaction, and cleaning is faster
Pour concentrated vinegar or essence into dirty places
Sorrel acid cope with mud, but do not apply it for a long time
Hold the product for 15 minutes and rinse thoroughly with warm water

How to clean the acrylic bath at home?

It is not worth using abrasive compounds and powders to clean acrylic baths. They scratch polymers and spoil the product. It is recommended to use such compounds as “Silit”, “Domestos”, “CIF”. Substances with large chlorine content (whiteness) should not be left for a long time, since they are absorbed into the pores of the polymer and cause its yellowing.

Instructions for cleaning acrylic bathtub with citric acid:

Dissolve a spoonful of substance in a glass of hot water
Sprinkle the fabric with the solution and apply to the pollution. You can wipe the entire surface of the bathroom
Rinse with warm water
You can use special products for plastic baths, this is Riton, Eago, Ravak, Delfin

How to bleach a cast -iron bath?

Cast iron bath can be cleaned using soda and abrasive substances. It is recommended to clean with liquid chlorine. Do not rub the metal surface with a scraper, it destroys the coating.

Instructions for cleaning the cast -iron bath:

Run the product with very hot water or boiling water
Wipe with a dry cloth or towel
Pour a little whiteness or liquid chlorine. You can purchase a pre -Mestos with chlorine or a hedgehog
Leave for 15 minutes, and then rinse with warm water

How and what to clean the bath with folk remedies?

There are many ways to clean the bathroom from rust and lime plaque. Of course, it is advisable not to apply the methods that destroy enamel.

Bathroom cleaning options with folk remedies:

Mix salt with vinegar and warm. Apply the solution to the surface. Wash off with water
Mix the drill with ammonia and apply to rust or dirt. Rinse everything after 15 minutes
Pour citric acid on the moistened surface and leave for 20 minutes. Wash the surface

How to clean the acrylic bath vinegar?

Acryl is a kind of material that requires careful care. On its surface is an antibacterial film that protects the container from mold and bacteria. It is not worth using white and aggressive substances for cleaning. Use verified and safe methods.

Acrylic cleaning instructions with vinegar:

Rinse the product with hot water, wipe dry
Dissolve 20 g of salt in 100 ml of vinegar and put in a microwave. The temperature will speed up the process and you will get rid of dirt faster
Pour the bathroom with a solution and leave for 20 minutes
Wipe with a damp cloth and wash it with water

How to clean a bath at home with soda?

Heat the bathroom with warm water and wipe your leisure. Mix food soda with calcified and apply to a wet bathroom. Do not wash off soda and let the paste dry. Pour vinegar into a glass and pour the surface to them. Vinegar and soda will enter into a chemical reaction and dirt will disappear.

You can use this way:

Mix soda with water until gruel is obtained
Apply the paste to the surface and leave for 20 minutes
Rub the surface with a sponge and rinse thoroughly

How to clean a bath with citric acid?

This method is used to clean the cast -iron and acrylic bathtub of lime and rust.

Cleaning instructions:

Drink contaminated places with warm water
Pour citic acid. It sticks to a damp surface, forming a concentrated solution
Leave for 25 minutes
Wipe with a clean cloth and rinse

How to clean a bath with hydrogen peroxide?

Hydrogen peroxide is usually used to clean the bathroom from yellowness. This is a weak acid that corrodes dirt. In this case, the solution does not smell of anything and completely safe for health, unlike chemicals.

Cleaning instructions:

Mix ammonia and peroxide in a ratio of 2 to 1
Apply the prepared solution on a warm and dry surface
Leave for 30 minutes
If the bathroom is very dirty, you can leave a fabric moistened in a prepared solution on the surface