How to shut up an entrance wooden or metal door with a dermantine, vinylskoye with your own hands: ideas, advice, rules. Beautiful lining of the entrance doors by dermantine, vinylska: photo

Instructions for upholstery on the door with dermantine.

Content

Very often people purchase old apartments in which a new front door is not installed. If you do not have the means to replace the reliable door that contains the insulation inside, in which case you can overtake the old door with dermantine.

How to shut up with dermantine or vinylskoye entrance wooden doors: ideas, tips, rules

It is worth noting that such a manipulation will not only decorate the appearance of the front door, but will also contribute to sound and thermal insulation. Therefore, dermantine sheathing is an excellent option to update the appearance of the leaf, make it more attractive, and also save heat in the house.

Instructions:

The upholstery of wooden doors is a fairly simple manipulation. To do this, you need upholstery material, insulation, nails. Before performing the work, you need to remove the old upholstery material, with the help of pliers to pull out all the nails. Next, you need to start choosing the material. Now the market is quite a large amount of upholstery from the substitute for the skin. It can be either cheap or expensive.
The price varies widely and depends on the lining, which makes up the upholstery, its appearance, as well as quality. Try to choose a fairly dense dermantine that does not stretch and behaves perfectly when cooling. Because some cheap species in the cold can burst or become very tough.
After you decide on the material, it is best to remove the sash from the loops and put on a perfectly even horizontal surface of the table. Work will be much easier. Now you need to measure the size of the sash itself and cut off 15 cm larger on each side. Such a margin is necessary in order to form a roller that should protrude beyond the sash.
Next, fix the insulation on the door. Most often, a special pressed fiber is used, as well as foam. Fasten the material on top with nails. Pull it down, fix it also on the sides.
Now you can apply the necessary pattern using nails with wide hats. It is necessary that the color of the hats be in the color of the inhabitant itself. You can do as you want and how much you want to have these nails. An additional number of nails contributes to the better holding of the material, and also prevents the rolling of the seal and insulation.
It is worth noting that now there is a dermantine with a rather poor insulation in the form of cotton wool on sale. Avoid the acquisition of such upholstery materials, because they can use moisture to slide, forming voids and bald spots. During the door upholstery, a foam lining will be an ideal option.
When the work is completed, it is necessary to proceed with the formation of the roller. To do this, you need to turn a dermantine several times and leave the threshold, which is approximately 5 mm. It is this threshold that will prevent passing air and sounds into the apartment. He will fit tightly to the door box.

How to shut up the input metal door with dermantine or vinilisk: ideas, tips, rules

The upholstery of metal doors is even easier than wooden. It is not necessary to remove the product from the loops. At the same time, the upholstery is carried out not by nails, but by ordinary glue.

Instructions:

You need to fix the insulation. This is a thin layer of foam rubber or thermal insulation material that is used in laying a laminate, foamed polypropylene.
Dermantine is already directly glued to this material. This is done at the edges.
There is no need to lubricate completely with glue. When everything dries, it is necessary to cut the remaining material along the perimeter of the wings.

Replacing doors upholstery: tips

There are tips that will help to perform work quickly enough and with minimal time and nerves. Initially, before the work, you need to dismantle the sash, as well as remove locks, loops, eyes. All these items will be superfluous, because it is impossible to perfectly cut out dermantine if the lock is installed. In these places it is necessary to glue dermantine and not use brackets.

Tips:

In order to simplify and accelerate the work, instead of nails, you can use a regular stapler, which is used in furniture production. It is they who consolidate dermantine on the door from above, below, as well as on the sides. You can also form a roller using a stapler.
For decor, it is necessary to use furniture nails with hats to the color of the upholstery. Dermantine serves about 7-10 years, does not burst, does not erase. If it seemed to you that the door is dirty enough, it is necessary to rinse it with a warm soap solution.
It is also recommended to lubricate such doors with a special cream that softens the material and prevents its cracking. The main disadvantage of such a finish is low fire resistance. The fact is that this material quickly flares up and promotes the spread of fire inside the apartment.

Beautiful lining of the entrance doors by dermantine, vinylska: photo

The upholstery from the vinylski is necessary in order to ennoble the appearance of the front door, to make it more attractive. Now upholstery is rarely carried out. This is mainly done from the inside in order to additionally give thermal insulation and adjust the door decor for the internal interior. It is for this purpose that the upholstery of a suitable color is selected. The most interesting thing is that the color of the material outside and inside the door may differ, and depend on your preferences. Below are photos of a beautiful door upholstery.

As you can see, dermantine is an excellent material in order to put the appearance of the front door in order. This will also help improve thermal insulation and prevent the spread of sound from the entrance to the apartment.