How often to clean the computer, for what, preparation of equipment, disassembly of equipment. How to clean coolers and video cards, power supply? How to assemble a computer after cleaning? What needs to be done so that the PC clogs less?

A computer is an assistant who has become indispensable in the modern world. It is important to properly care and clean the equipment when clogging.

Content

A very common problem due to which the processor of a personal computer overheats is a poor ventilation that forms in the system unit of equipment. As a result of this, the PC begins to work more slowly over time, overheating, and unexpectedly overload. Sometimes, for the same reason, important components of equipment are conceived conceived. This is all just happening due to dust accumulated inside the dust system.

How often to clean the computer, for what?

Constant cleaning of a personal computer from pollution can significantly extend the functionality of the technique. As the instruction shows, which is offered by PC manufacturers - cleaning should be done at least 1 time in 1 year. However, in fact, this should be done once every 6 months, or maybe even more often. Since people use computers without a break for 12 hours or more. We advise you to clean the PC more often. A couple of times a year you will be enough, even if you take into account the large load of the equipment.

The inside of the PC consists of the following components:

Motherboard
Video cards
Central processor
Power supply and other important elements that need to be constantly cooling from the outside

While using the technique, these components tend to heat up hard. When heating occurs, it should immediately overheat it. So that the equipment does not overheat, for each part, which is very heated, coolers that cooled due to the air flow were invented. Such coolers tighten dust into the system unit during operation, since air flows are directed precisely into the computer.

When there is a lot of dust, it begins to stick on the board of the system unit, on the surface of the hard drive, video card, and therefore the conductivity and sensitivity of each board and connector very much decreases very much.

This circumstance is caused by the fact that the personal computer begins to bug and slow down. The technique can slow down while watching videos that have increased resolution, freeze in a particular game, and so on. If the technique is very contaminated, then it is sometimes even impossible to open ordinary folders with data, and therefore it is not worth complaining about the computer itself.

Next a sign that a PC must urgently clean - This is the buzz or rattling of every cooler, severe heating. This happens, as a rule, in laptops, since it is according to these details that you can easily find out that the equipment is overheating. If you take a stationary computer, then it begins to heat up hard, if the equipment is terribly dirty inside. Also, if the holes are almost completely filled and almost completely filled with dirt, through which the cool air is absorbed.

How often you need to clean the computer: preparation of technology

In order to clean a qualitatively personal computer, you need to consider the following important points.

Before you start cleaning the equipment, prepare such tools:

Pencil. It is necessary to arrange marks on each wire and connector so that you can quickly install elements in your own places. You can also use a digital video camera, preferably with excellent quality. Take a picture of each wire, a sequence of assembly of wires.
Brushes. Buy 2 brushes in advance. One brush should have a solid bristle, the other brush is soft. The first option is suitable in order to remove the adhesive dirt in any inaccessible place. The second option allows you to clean the wires and joints.
Screwdriver. Take the cross. Thanks to it, you will unscrew different screws, remove the details.

A vacuum cleaner. This technique is considered the most important weapon during the struggle against large dust.
A cylinder filled with compressed air. This cylinder, under high pressure, can produce an air flow, blowing out the dust itself even from hard -to -reach areas.
Rubber gloves, respirator. Protective funds will never hurt.

How often you need to clean the computer: Dismantling of equipment

From the very beginning, turn off the supply computer wire. Disconnect the entire periphery from the outlet.

Then pull out the system unit, put it in a comfortable place where it will be more convenient for you to work. Find a bolt on the back surface on the system unit.
Scroll it with your finger, while holding the block covers. You will do it very quickly.
When the covers are removed, put the PC on the side. It is in this situation that you will open access to each part.

Pull out the RAM. On the two sides of these modules are the latches that hold them. Make sure that you disconnected them completely.
Remove the video card. It rests at the expense of a special screw from the outside of the system. Unscrew the screw using the cross screwdriver. Also find a special latch, which is placed near the video card chip.
Press it and pull it until you hear a click. In which direction it will be easier for you to pull the part, pull it there. Do not put a lot of effort.
Also, if you want, disconnect the hard drive. But you can simply wipe it with a piece of fabric.

Cleaning PC from dust: how to do the right thing?

First, remove large pollution. Here you can use the vacuum cleaner. Before starting the process, disconnect the metal tube, put only the hose on which the plastic tip is worn. Included with a vacuum cleaner, as a rule, there is a nozzle with brushes. It is thanks to her that you quickly clean the equipment, do not spoil the wiring.

Before pressing the Power button, set the minimum power and, if necessary, add the power yet.

How to clean coolers and video cards?

This process can be divided into the following stages:

Stage 1 - external pure.
Stage 2 - internal cleaning.

External cleaning is the use of a vacuum cleaner, thanks to which dust is collected. Add power on the vacuum cleaner, because you can’t just damage the coolers. You can even bring the hose very close to them. The screw that sucks the air will spin from the vacuum cleaner, as a result of which the dust will go to the hose.

In that case, if the coolers are very noisy, you will have to clean all the internal details. It is very difficult to clean the cooler located on the video card. Therefore, the video card must first be disassembled. We note that before disassembling you need to buy a thermal grease, which is sold in a specialized store.
Disconnect the video card from the board, turn over the side where there is no radiator with cooler up. The wires that connect the fan and the video card are removed from the connector. On the back of the video card, unscrew the screws protruding upwards, remove the radiator.
Try to do everything carefully Carefully, because under the radiator there is a processor with a thermal package applied. After several years of work, the paste has the ability to dry to the radiator. Therefore, heat the radiator with a hairdryer, pull it a little by a couple of millimeters, rotate it, and then disconnect from the card.
There is a sticker in the back of the fan. Remove it, there will be a bearing under it. Drill little there to grease the coolers, spin the fan. So the grease is evenly distributed throughout the cooler axis. Remove excess lubrication using a piece of fabric.

In order to glue the sticker back, wipe this area with alcohol. When sticking the sticker and fix the fan, treat the central processor with a thermal, applying it with a thin layer. Collect the equipment in the reverse order.

Then wipe each contact with cotton wool, soaking it in advance with alcohol. The cooler, which is on the processor, clean the identical method. But before that, elk the mounts, twist the screws.

How to clean the power supply?

In order to clean the power supply, buy a cylinder. Filled by compressed air. The power supply is considered the device that is poorly extracted. You will have to unscrew a lot of screws and disconnect a large number of wires. An important condition - put the mark on each wire and connector, so that then everything is installed faster in place.

Unscrew the power supply on the outer side of the equipment. Having performed the dismantling of equipment, remove the cover from the power. Having opened access, feel free to use the cylinder in order to clean the equipment.

How to assemble a computer after cleaning?

When you completely clean the PC from pollution, collect the system unit correctly. This process repeats every step that was performed during the disassembly of the technique, only in the reverse order.

When connecting the connectors from the wire in the power supply, close the lid, connect the external parts. During the assembly, be extremely careful so that the nodes stand in their own places.

What needs to be done so that the PC clogs less?

There are some important recommendations with which you will not take a vacuum cleaner so often to clean the computer:

Place the PC at a special distance from the wall. This is necessary that the entire cooling system function normally.
When you carry out wet cleaning in the apartment, be sure to wipe the PC and the system unit.
Try to clean the PC and other such equipment every 6 months.
Equipment, which is located near the source of drafts, can be polluted faster. Therefore, ventilate the room only when the device is turned off, so that the coolers are pulled into the PC dust.
Never open the holes under the fans in the system unit of the device. As a result of this, the PC will be very hot.