From what and how to sew a turban, a turban with your own hands: ideas, patterns, photos

In this topic, we will consider how to sew a turban.

Content

Famous designers increasingly began to create new and vivid images, the main accent of which is the turban. After all, such a headdress saves if there is no time for a hairstyle or I want to make a note of femininity and sophistication in your image.

And if you do not want to spend time every time by twisting the structure, then you can immediately sew a turban that you will not need to be tied. There are several variations that we will talk about now.

What fabric can be used to sew a turban?

Before grabbing the process in order to sew a turban, it is important to choose the right material. Most often, Muslims used silk or brocade, but you can use completely any fabric that you like. The only condition is that it should be soft. It can be Delicate silk, cashmere or velvet.
If you make a turban for the cold season, then give preference Half -haired fabric.But do not take too rough or thick canvases, otherwise all her femininity and tenderness will deteriorate.
You should also not choose linen, T.K. It is too hard and will form ugly and rough bends. The felt is also not suitableat a minimum, the headdress will look ridiculous and cheap.
And the knitted material is too thin and will stretch very quickly. Although as an affordable analogue is very often used.
Great wool, velvet or cotton,t.K. These materials will be quite dense and will hold well.
For winter cold, you can even use Short -haired fur.

With such a hats, you will always be feminine

How to sew a turban: a simple way

It is necessary to take a piece of fabric with a treated lower edge and bend in half along the length, so that it turns out a rectangle of 60 by 30 cm. That is, the initially the length of the product should be at least 100 cm. The fabric must be folded with the front side inside.

Now you need to make a slight rounding on the upper right corner.
Sour the upper and lateral edge, and then stitch. Keep in mind that the thread should not be cut off. It is still useful to pull the product for the formation of folds. By the way, it is more convenient to carry out this manipulation directly under the paw of the sewing machine.
Now, for convenience, pull the hat on a can or mannequin, turning it onto the front side.

Return literally 3-4 fingers from the alleged middle of harvesting (somewhere at an altitude of 10-12 cm from the edge) and begin to form folds. As can be seen in the above photo, the fabric must be laid out in the form of a Christmas tree on each other. Come in as many rows as folds will form.
Their value also plays a role - the more capture, the less folds will be required. Fasten the thread so that they are fixed.
Cut the remaining tail. Do not forget to leave 2 cm for processing only for processing. This land must be carefully hidden in folds and pissing.

Next, the product must be turned back to the wrong side and process the occipital part, gently collecting it. If necessary, adjust the seams and assemblies.

Video: A simple way to sew a turban

How to quickly sew a turban?

This option will require only two sizes and basic sewing skills. Measure the volume of the head - we will take 52 cm following the example. Now you need to measure the length from the hollow between the nose and forehead up to 7 vertebra, that is, at the bottom of the cervical region. You need to go with a tape through the forehead, the contour of the head and the back of the head is 47 cm.

Important: you can do even easier - take the size of 7 vertebrae to a jugular hollow. When you sew the hat, it remains to just pull it in front and decorate it with a brooch. If necessary, you can slightly adjust the product from behind, creating a small screed.

If you have too thin fabric, then fold it in half. But in this case, the length of the product must be taken 2 times greater (47*2). Next, as shown by the pattern below, we fold the fabric in the width also in half and make rounding from the corner to the middle.

We cut out and go through the cut along the cut perimeter. But we do not cut the thread, but use it to pull the segment. We tighten until we get a small hole 1-2 cm in diameter. You can’t turn it out, so you lay the line as close as possible to the edge. Fasten the corners to make a ring.

Cut the jumper in the shape of a rectangle, but round the edges. And also fold the fabric in half, the front side inside. Do not stitch the middle! This hole is necessary to turn out the product. After it can be flashed. If the fabric does not pour out, then this is not necessary.
Insert the jumper into the middle of the hole and turn the seam to the wrong side. Pass with a manual line along the cropped edge, fixing the jumper itself at the same time. Return to the front side and beautifully tie the tape, creating beautiful petals.

You can choose decoration at your discretion

Note: By this principle, you can make a hat a hat with a rim. To do this, you only need to seize the bandage, which is equal to the girth of the head to the collected basis. You can also launch contrasting shawls for decoration.

Video: How to sew a turban quickly?

Exquisite option, how to sew a turban

For the pattern, we need the volume of the head, which is 52 cm in our example. The width of the product is offered for consideration of 20 cm, but you can take up to 50 cm from this. Then more folds will come out, and the cleaning will turn out to be more voluminous. And yet - the length of the product in the example of 70 cm, but the longer the “tails” of the cap, the more revolutions you will have.

Important: only the pattern diagram is shown in the given figure. Therefore, take into account the proportions when compiling and do not forget about smooth rounding.

The pattern provides for sewing from two parts. Therefore, in order not to spoil the front side, work with the pattern on the wrong side, fastening with pins a canvas folded in half.
Cut the elements pass by overpowing a line and a zigzag pattern. This step can be skipped if the fabric does not pour. Although light materials are just most prone to this.
Sew the parts with each other with a fairly small seam along the rounded perimeter, but leave 2 cm for holes at a height of 8-10 cm.
On the front side, when the seams were smoothed out, go through the finishing pattern for their fixation.
Pass around the entire perimeter of a almost ready -made headgear, they will literally be 1 cm of fabric, with a usual line.

Make a jumper in the shape of a rectangle of arbitrary size. But keep in mind that the “folding bridge” creates a more interesting assembly if it has a width of 4-5 cm, and 1-2. Sprinkle from the wrong position, turn out and sew the ends, already passing through the hole.
Now the matter is for the "tails" of the heating. They can simply be taken to the front side, pass through the jumper and tied it. But if the length allows, then circle them in front, but for the tie, get back.

Note: You can bring out and tie a cute bow in front.

Making a turban with your own hands is quite simple and fast. Such a product must be in the wardrobe of every woman. Even if you did not have time to make a beautiful hairstyle, then put on an elegant turban in which you will always look elegant and feminine.