Ways to remove the residues of the sealant from various surfaces.
Content
- Silicon Construction, construction sealant - than dissolves: solvents
- How to quickly remove silicone sealant from tiles, tiles: photo
- How to quickly remove silicone sealant from your hands?
- Video: How to remove installation foam from hand?
- How to quickly remove silicone sealant with an acrylic bathtub?
- How to quickly remove silicone sealant from plastic, windows yourself?
- How to quickly remove silicone sealant from clothes yourself?
- How to quickly remove silicone sealant from glass?
- How to quickly remove silicone sealant from the countertop?
- How to quickly remove silicone sealant from the floor?
- Video: How to remove silicone?
The best construction sealant - Silicone. The properties of water resistance, durability, elasticity make it possible to seal any surface. Ease of use and strength of protective seams give it greater popularity in use. With all its positive properties, there is one small negative nuance - the sealant penetrates deep into the structure of the material.
How to cope with traces of inaccurate work or remove the already worked out sealant? We will consider the answers to these questions in the proposed article.
Silicon Construction, construction sealant - than dissolves: solvents
To dissolve hardened silicone sealant, solvents are used:
- Liquid - applied with a tampon
- Aerosols - shaking before use
- Pastes - distributed by a small spatula
Under their influence, the silicone sphere softens or turns into an easily washed mass that is quietly rubbing.
Sometimes under the influence of these substances, the processed plane is damaged. To avoid such a problem, it is recommended to carry out trial work on a separate piece to check the harmless solvent for the base.
The structure of the sealant is different, therefore:
- From the remains acid foam We get rid of concentrated 70% essence
- Foam on the basis of alcohol We remove 100 % alcohol solution
- Neutral seal It is perfectly removed: white spirit, gasoline, acetone
- Without knowing the composition of the sealant, it is better to use the factory means that are acceptable For various foam:
- Dow Corning OS-2
- Dow Corning DS-2025
- Penta - 840
- Antisil
How to quickly remove silicone sealant from tiles, tiles: photo
We clean the tile from foam, combining mechanical and chemical methods for this:
- We remove the wide part of the remains of the material with a sharp knife or razor. We try not to touch the level of bath and tiles
- On the remnants of the sealant, apply a remedy for dissolution
- We withstand 2-3 hours
- After softening, the foam will look like jelly, pry it with a knife and remove it completely from the tile
- Next, wipe the traces of the sealant with a dry cloth
- It happens that after cleansing, a dark spot appears on the surface. We remove it with sodium salt wrapped in a wet cloth
- In some cases, the sealant is removed not by a holistic ribbon. This may be due to an incorrectly chosen drug for softening or selected foam of a bad brand. Then we process the surface impregnated with a solvent by a rag several times, achieving the sling of the seal. Next, remove the resulting spools with a rag
- In the case of removal of foam from porous tiles, softened sealant is removed with a pumice or a spicy scrap
How to quickly remove silicone sealant from your hands?
Persistent silicone sealants after solidification are firmly attached to the plane.
If the mounting foam has been held on the skin, we accept instant actions:
1 method
- With a soft rag, remove the product without rubbing
- The entire sealant will not be able to immediately remove, so we remove the remains of the thin film: gasoline, acetone or varnish removal.
2 method
- We lower our hands into a warm salty solution, withstand for several minutes
- Then remove the foam with a pumice or hard washcloth
- We repeat the procedure 2-3 times, since immediately the sealant will not be able to remove
3 method
- Soapy soap soap and rub polluted places
- We maintain 10 minutes
- Remove the remaining foam with a sponge
4 method
- Warm vegetable oil and washing powder well wipe the skin in the pollution zone
- Then we carefully wash my hands
5 method
Pre -acquired special napkins will facilitate the laborious path of removal of the sealant.
- It is enough to rub their hands with them, and unnecessary pieces of foam will instantly be removed
Video: How to remove installation foam from hand?
How to quickly remove silicone sealant with an acrylic bathtub?
The surface of the acrylic bathtub is very sensitive to mechanical damage.
Therefore, we very carefully do the following manipulations:
- We apply a special tool for the Dow Corning OS-2 or White-Spirit on frozen sealant
- After softening the foam, remove it with a wooden scraper
- Remove the remaining traces with a rag
How to quickly remove silicone sealant from plastic, windows yourself?
Since silicone has a slight adhesion with plastic, it is very easy to remove with any of the above solvent for foam.
- Apply a foam
- Hold about an hour
- Rinse any degreasing solution
How to quickly remove silicone sealant from clothes yourself?
To cope with pieces of the seal that lingered on the fabric can be in several ways:
- We wash at a temperature above 40 degrees. Fresh sealant is well removed with washing
- Polymerized sealant with dense plain tissues is removed with a solvent for foam. We soak for 40-50 minutes. We forgive at a temperature of the permissible for fabric.
- We clean colored fabrics using a mechanical method. We pull and fix the spoiled robe on a smooth plane. Softly scrap a knife or wire brush. Rinse the remains with: alcohol, vinegar, gasoline or white spirit. We soak, wash the costume.
How to quickly remove silicone sealant from glass?
As well as from plastic material, the seal is very simply removed from the glass surfaces.
We do this in any of these methods:
- A blade or sharpened spatula neatly scraped glass, in places where you need to remove foam
- We wipe the glass with a specialized tool: Penta-840, white spirit, gasoline
- We heat the glass in any possible way. Remove the melted foam wrapped in wet salt with salt
How to quickly remove silicone sealant from the countertop?
In order to get rid of foam from countertops, you need to know the surface of the surface.
- We clean porcelain stoneware with any existing methods: mechanical, chemical or combined
- For a plastic base, we use:
- A neat mechanical method: a sharp knife, a wet rag with coarse salt, iron washcloth, detergents
- Any chemical composition, after the sample of the material for compatibility with the used solution
How to quickly remove silicone sealant from the floor?
Given the basis of the floor surface, we select one of the above methods.
You can add only another method that was not described earlier:
- We apply a re -fresh sealant on the already captured, in the proportion of 1: 1
- After softening the old layer, remove it with a spatula moistened in a soap solution
- We wash small residues with a solid washcloth or sponge with the addition of detergents
To get rid of silicone sealant is a difficult task. The best option is to prevent the appearance of excess foam on any site.
- Use gloves and a suit that completely cover the body
- Apply the seal to small areas, squeezing it in small portions
- Protect the place with polyethylene where there should not be foam